学步园

原文：http://blog.scottlowe.org/2012/11/05/compiling-libvirt-1-0-0-on-ubuntu-12-04-and-12-10/

In case you hadn’t noticed late last week, the open source virtualization API project libvirt released
version 1.0.0—a major milestone, obviously. To celebrate the 1.0.0 release, here are instructions for compiling the libvirt 1.0.0 release on Ubuntu 12.04 and 12.10.

(If you need instructions on compiling an earlier release of libvirt on Ubuntu, see this
post. It works for libvirt 0.10.1 and 0.10.2 on Ubuntu 12.04 LTS; I haven’t yet tested it on Ubuntu 12.10.)

These instructions assume that you have built a plain-jane Ubuntu system (either 12.04 LTS or 12.10). I tested these instructions on an Ubuntu 12.04.1 LTS VM, freshly built and updated using apt-get
update && apt-get upgrade, on a freshly-built Ubuntu 12.01 VM (also up to date), and a physical system running an up-to-date instance of Ubuntu 12.04.1 that also had KVM and an earlier version of libvirt installed. These instructions worked in all three
cases.

Ready? Let’s get started!

1. Download the libvirt-1.0.0.tar.gz tarball from the libvirt.org
   HTTP server.

2. Extract the tarball using tar -xvzf libvirt-1.0.0.tar.gz.

3. Using apt-get, ensure that the following packages are installed: gcc, make, pkg-config (already
   installed in my testing), libxml2-dev, libgnutls-dev, libdevmapper-dev, libcurl4-gnutls-dev, and python-dev. (Interestingly enough, earlier versions also required libyajl-dev, but this version didn’t seem to need it.) You can probably omit the libcurl4-gnutls-dev
   package if you don’t want ESX support; I did want ESX support, so I included it.

4. From within the extracted libvirt-1.0.0 directory, run the configure command. I specified particular
   directories because that’s where the prebuilt binaries from Ubuntu are normally placed. I’ve line-wrapped it here for readability:

   ./configure --prefix=/usr --localstatedir=/var \
   --sysconfdir=/etc --with-esx=yes

5. The above command does not include Xen support; if you need Xen support, you’ll need to add --with-xen=yes to
   the command, and your list of prerequisite packages will change (there are additional packages you’ll need to install).

6. Once the configure command completes, then complete the process withmake and make
install. Note that I used sudo make install here because I’m installing files into privileged system locations.

   make
   sudo make install

7. Finally, to verify that everything seems to be working as expected, restart libvirt with initctl stop
libvirt-bin and initctl start libvirt-bin. (Yes, you could use initctl
restart, but this allows you to see the clean stop and start of the libvirt daemon.) As an aside, note that this step only works if you either a) had a previous version of libvirt installed, or b) create theinitctl job
   for libvirt. I chose the first approach.

8. As a final verification step, run virsh --version or libvirtd
--version to verify that you’re running libvirt 1.0.0.

That’s it! Now, as others have pointed out, this will create some potential system administration challenges, in that apt-get will still suggest new libvirt
packages to install when you try to update the system. I think that there are some commands you can run to keep the manually compiled version instead of the version apt-get is
suggesting, but I haven’t yet determined exactly which commands to use. (If you have more information, please speak up in the comments!)

I have a series of new libvirt-related blog posts in the works, so stay tuned for those. In the meantime, feel free to post any questions, corrections, or clarifications in the comments below. Courteous comments are always welcome.